- 您现在的位置：买卖IC网 > Sheet目录870 > NDTD4815C (Murata Power Solutions Inc)CONV DC/DC 3W 48VIN 15VOUT DIP24
NDTD Series
Isolated 3W Wide Input Dual Output DC/DC Converters
OUTPUT CHARACTERISTICS
Parameter
Voltage set point accuracy
Conditions
With external input/output capacitors
3.3V & 5V outputs
12V & 15V outputs
Min.
Typ.
±2
±1
Max.
±5
±3
Units
%
Line regulation
Low line to high line with external input/output capacitors
0.15
0.5
%
Load regulation
25% load to 100% load with external input/output
capacitors with balanced load
3.3V & 5V outputs
12V & 15V outputs
0.5
0.2
1.0
0.5
%
%
Ripple
Ripple & noise
BW = 20Hz to 300kHz with external input/output capacitors
BW = DC to 20MHz with external input/output capacitors
15
90
40
150
mV rms
mV p-p
NDTD05XXC, NDTD1203C,
% voltage change on negative output when
NDTD1205C, NDTD2403C,
NDTD2405C, NDTD4803C,
5.0
Cross regulation
positive load varies from 12% to 50% of 3W rating,
with negative load ?xed at 50%
NDTD4805C
NDTD1212C, NDTD1215C,
NDTD2412C, NDTD2415C,
2.1
3.0
%
NDTD4812C, NDTD4815C
Short circuit protection
GENERAL CHARACTERISTICS
Continuous
Parameter Conditions
Min.
Typ.
Max.
Units
Switching frequency
100% to 25% load, VIN min to max
60
620
kHz
TEMPERATURE CHARACTERISTICS
Parameter Conditions
Operation
Storage
Min.
-40
-50
Typ.
Max.
85
130
Units
NDTD0503
54
Case temperature rise above
ambient in still air
NDTD1203C, NDTD2403C, NDTD4803C
NDTD0505C, NDTD0512C, NDTD1205C, NDTD2405C, NDTD4805C
NDTD0515C, NDTD1212C, NDTD1215C, NDTD2412C, NDTD4812C, NDTD2415C,
NDTD4815C
40
35
28
oC
ISOLATION CHARACTERISTICS
Parameter
Isolation voltage
Resistance
Conditions
Flash tested for 1 second
Viso=1KVDC
Min.
1000
1
Typ.
Max.
Units
VDC
GΩ
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NDTD series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NDTD series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NDTD series has an EI ferrite core, with no additional insulation between primary and secondary windings of enameled wire. While parts can be
expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane)
is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly
advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
www.murata-ps.com/support
KDC_NDTD.E05 Page 2 of 7
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
NDTS0505C
CONV DC/DC 3W 5VIN 5VOUT DIP24
NDXD4815EC
CONV DC/DC 7.5W 48VIN 15VOUT DIP
NDY4805C
CONV DC/DC 3W 48VIN 5VOUT DIP24
NFA31CC222R1E4D
EMI FILTER 2200PF 200MA SMD
NFA31GD4706R84D
EMI FILTER 47PF 50MA SMD
NFM18CC470U1C3D
FILTER LC HIGH FREQ 47PF 0603
NFM18PC225B1A3D
FILTER LC HIGH FREQ 2.2UF 0603
NFM18PS474R0J3D
FILTER LC HIGH FREQ 470000PF 060
相关代理商/技术参数
NDTL03N150CG
制造商:ON Semiconductor 功能描述:NCH 2.5A 1500V TO3P3L - Ammo Pack 制造商:ON Semiconductor 功能描述:FNFLD - NCH 2.5A 1500V TO3P3L
NDTM104K35F
制造商:NIC Components Corp 功能描述:- Bulk 制造商:NIC Components Corp 功能描述:NDTM Series 0.1 uF 10 % 35 V Radial Resin-Dipped Solid Tantalum Capacitor
NDTM104K35F1TBF
制造商:NIC Components Corp 功能描述:- Ammo Pack
NDTM104K35F1TRF
制造商:NIC Components Corp 功能描述:CAP 0.1UF 35VDC 10% 4.5 X 7MM RDL 2.5MM 1% - Tape and Reel
NDTM104K50F
制造商:NIC Components Corp 功能描述:- Bulk
NDTM105K20F1TRF
制造商:NIC Components Corp 功能描述:CAP 1UF 20VDC 10% 4.5 X 7MM RDL 2.5MM 1% - Tape and Reel
NDTM105K20F2TRF
制造商:NIC Components Corp 功能描述:CAP 1UF 20VDC 10% 4.5 X 7MM RDL 5MM 1% - Tape and Reel
NDTM105K25F1TBF
制造商:NIC Components Corp 功能描述:- Ammo Pack